What each option is
A 200A service upgrade changes the home's main electrical service so the utility, meter, service entrance conductors, main disconnect, grounding electrode system, and panel capacity support a larger calculated load. A subpanel addition keeps the existing service size and adds a feeder-fed panelboard for more breaker spaces near a garage, addition, workshop, HVAC equipment, or EV-ready area. In Texas, the code distinction matters: NEC Article 220 governs the service load calculation, NEC Article 230 governs service entrance equipment, NEC Article 250 governs grounding and bonding, and NEC Article 408 governs panelboards and circuit directories. The service upgrade solves capacity; the subpanel solves distribution. Mixing those two goals is how homeowners buy a panel that still cannot legally carry the planned loads.
State-specific factors
The state-content seed makes this a Texas comparison, not a generic national one. It lists Dallas, Houston, Fort Worth as the deepest directory metros, identifies Texas Department of Licensing and Regulation (TDLR) — Electricians (https://www.tdlr.texas.gov/LicenseSearch/) for the electrician licensing path, and summarizes licensing this way: Texas does not license general contractors at the state level. The Texas Department of Licensing and Regulation (TDLR) licenses Air Conditioning & Refrigeration contractors and electricians. It also gives the Electrical work cost band as $200-$9K with $1.7K typical. The companion buyer-guide context uses the same state-trade source data to ask who pulls the permit, which credential applies, what insurance proof is required, and what inspections close the job. Standards references are included to frame scope, but the adopted local edition still controls. Where the seed does not publish utility tariffs or local amendments, this guide names that gap rather than filling it with guesses. Use the written bid to connect every cost assumption back to those source facts. Ask bidders to attach model numbers, permit responsibility, warranty labor, and excluded repair work to the same line-item scope. The climate planning lens is long cooling seasons, peak electric demand, Gulf humidity in the east, and hotter dry markets in the west make utility capacity and load calculations decisive. For electrical work, the practical question is whether the house needs new service capacity or only more breaker space near a load cluster. A 200A service upgrade depends on NEC Article 220 load calculation, NEC Article 230 service equipment, meter location, grounding, utility disconnect/reconnect timing, and local inspection scheduling. A subpanel addition depends on feeder ampacity, panelboard rules under NEC Article 408, working clearances, and whether the existing service has capacity left. The seed does not publish utility service rules, so the utility must confirm any meter, service lateral, or overhead drop work.
Cost comparison
Service Upgrade (200A)
$1.7K-$9K
Uses the typical-to-high electrical band because service equipment, utility scheduling, grounding, and exterior work may be involved.
Subpanel Addition
$200-$1.7K
Uses the low-to-typical band when the existing service has spare load capacity and the feeder route is clean.
Source band: Electrical work: $200-$9K (typical $1.7K)
The state-content costBand for Texas lists Electrical work at $200-$9K with $1.7K typical. A subpanel addition normally occupies the low-to-typical part when the existing service has spare calculated capacity and the feeder route is clean. A 200A service upgrade moves toward the typical-to-high part because it can include meter work, service entrance conductors, grounding electrodes, main panel replacement, utility scheduling, exterior repairs, and inspection coordination. The low-to-typical spread is $1.5K; the typical-to-high spread is $7.3K. Treat that second spread as the premium for real capacity, not just more breaker slots.
Permit / inspection differences
Use the Texas licensing primer first: Texas does not license general contractors at the state level. The Texas Department of Licensing and Regulation (TDLR) licenses Air Conditioning & Refrigeration contractors and electricians. The trade entry points to Texas Department of Licensing and Regulation (TDLR) — Electricians (https://www.tdlr.texas.gov/LicenseSearch/), with ProFix license slug electrician-license-in-tx. Local permit offices still decide the exact permit type, adopted code edition, and inspection sequence. A 200A service upgrade normally needs an electrical permit, utility coordination, service disconnect/reconnect, grounding and bonding inspection, panel labeling, and often a release before the utility energizes. A subpanel addition also needs an electrical permit, but inspection focuses on feeder size, overcurrent protection, neutral-ground separation, working clearances, and circuit directory. The subpanel avoids utility work only if the existing service load calculation passes.
Verdict by scenario
Verdict Texas: 200A service upgrade Texas versus subpanel addition Texas. Choose 200A service upgrade Texas when Texas load math fails, Texas EV or heat-pump loads are planned, Texas service gear is unsafe, and Texas utility work is unavoidable. Choose subpanel addition Texas when Texas load math passes, Texas breaker spaces are gone, Texas new circuits cluster nearby, and Texas utility disconnect risk can be avoided. Compare Texas capacity calculations, Texas feeder routing, Texas grounding, Texas utility timing, and Texas inspection release before signing.